DRI WASH N GUARD® is a
combination car wash, polish and protective glaze which is
applied directly to a dirty surface without the use of
water, it contains no waxes, nor is it simply a polish.
Waxes do a good job of
"protecting" but often leave the paint dull. Polishes are
great at removing minor stains and blemishes, and are much
more capable of rejuvenating dull paint. But polishes often
are abrasive, and provide very little protection on the
paint surface. Paint sealants protect very well, but cannot
clean or polish. A vehicle's paint must be virtually
pristine before the sealants can be applied. DRI WASH 'n
GUARD® combines the best features of waxes, polishes and
paint sealants without any of the drawbacks.
Top
DRI WASH 'n GUARD® contains
47 ingredients, including wetting agents, lubricants and
protectants which have never been used by the car care
industry.
The detergents and wetting agents in DRI WASH 'n GUARD®
combine to soften and emulsify surface grime, while a
specific blend of polymeroxane fluids and hydrophenolic
lubricants attach a microscopic layer of exclusive
PolyGuard-3® to the surface. PolyGuard-3® is an extremely
rare (and expensive) substance which provides a bonded layer
of protection against any remaining abrasive not broken down
by the detergents and wetting agents.
Top
It's EASY, All you need
is two soft terry towels-a small washcloth and a hand towel.
Wet the smaller one with water until it is almost dripping,
then lightly run over the area to be cleaned (such as the
hood). DO NOT RUB HARD. The dirt and water will not stick to
the DRI WASH 'n GUARD® on the surface. Now take the dry,
larger towel and lightly buff the area dry. That exclusive
DRI WASH 'n GUARD® shine will come right back. Ordinarily,
one wetting of a small washcloth is enough to finish an
entire car.
A little common sense
will help here-if your car is really dirty with caked mud,
pebbles, etc. remove it from the surface with care.
Top
When used in strict
compliance with its "directions for use," DRI WASH 'n GUARD®
is guaranteed to perform as indicated. Upon initial use, the
bottle will spray properly and the vehicle will shine more
than before DRI WASH 'n GUARD was applied and water will
bead on it.
Years of ongoing test
evaluations, quality control assurances, and hundreds of
thousands of field test cases that our satisfied customers
have given DRI WASH 'n GUARD® assure its safety and
effectiveness. DWG International© , however, cannot be held
responsible for damage that may occur from improper use of
the product.
Top
A vehicle surface protected
by DRI WASH 'n GUARD® will bead water for a year or more,
even on windshields which are scrubbed by wiper blades, ice
scrapers, etc. When applied to paint on a new vehicle, then
reapplied twice a year, the paint will not fade. Once
oxidation begins, however, it cannot be stopped, only
slowed. On older, extremely oxidized paint, DRI WASH 'n
GUARD® may need to be applied as often as every 2-3 months,
even though the paint is still protected and beading water.
DRI WASH 'n GUARD® helps protect against the effects of high
sun exposure, acid rain and road salt.
Top
Mud, clay, granules, heavy
salt spray, bugs, heavy tar and tree sap are examples of
things that cannot and should not be polished with DRI WASH
'n GUARD®. Let common sense be your guide-if in doubt, rinse
off the vehicle before applying DRI WASH 'n GUARD®.
Top
There is no other product for
use on glass which will give the brilliant clarity of DRI
WASH 'n GUARD®. The glass will seem to disappear. The
product also makes a glass surface smoother, or slippery, so
that water runs off a windshield without a trace. This
"slick" surface also means that insects, bird droppings and
tree sap can be removed effortlessly. In winter, windshields
and outside mirrors protected by DRI WASH 'n GUARD® are more
easily cleared of snow and ice.
Top
Should DRI WASH 'n GUARD® be applied over paint and
sealants?
Yes and no. Paint sealants
are only applied to new cars, or cars whose paint is in
excellent condition. If properly applied, the sealant will
maintain the finish for six months or more. When the finish
no longer beads water, the DRI WASH 'n GUARD® should be
applied. DRI WASH 'n GUARD® should not be applied within 90
days after a fresh paint sealant.
If DRI WASH 'n GUARD® is applied over FRESH paint sealant,
it is possible that the DRI WASH 'n GUARD® may be somewhat
difficult to remove and cause minor streaking, usually
noticeable only on darker colors. It can be applied over a
fresh paint sealant without problems if a high-speed buffer
is used.
Top
Can DRI WASH 'n GUARD® be applied over other waxes and
polishes?
Yes. It will cut through any
wax or polish and leave a brilliant, bonded layer of
protection.
Top
If I decide to wash my car before applying DRI WASH 'n
GUARD®, must I dry it, to?
A big YES here! Even a few
drops of water will create problems, i.e. the polish will be
difficult to remove and will probably leave streaks.
Furthermore, DRI WASH 'n GUARD'S® shine and protection
qualities will be greatly diminished.
Top
What
happens if DRI WASH 'n GUARD® freezes?
DRI WASH 'n GUARD® has been
subjected to repeated cold-cycle tests to -20 degrees F.
with no damage to the chemical formulation. However, the
bottles in which the product is packaged will become brittle
and subject to breakage in sub-freezing temperatures. It is
recommended that DRI WASH 'n GUARD® be stored at room
temperature.
Top
Does DRI
WASH 'n GUARD® contain silicones?
No.
Top
Why
shake DRI WASH 'n GUARD before each use?
Some of the product's
ingredients fall out of solution and must be remixed before
use. Vigorously shake the 32-oz bottle prior to filling the
8-oz. AIRosol applicator bottle, then shake it before each
application of DRI WASH 'n GUARD®.
Top
Can another type of spray bottle be used to apply DRI WASH
'n GUARD®?
Possibly, but doing so will
nullify the product warranty. There is no other spray
applicator which provides the fine, even mist which is
dispensed by the AIRosol bottle
Top
What
is the useful life of the AIRosol bottle?
Properly handled, the bottle
will last indefinitely. Each bottle is hand-tested before it
leaves the factory and is warranted to be in perfect working
order. It should not be dropped, and it should be stored in
an upright position at room temperature, if possible.
The spray valve needs periodic cleaning. The simplest way to
clean it is to invert the fully pressurized bottle and
depress the actuator button for three seconds. If the valve
is extremely clogged, remove it and soak it in hot, soapy
water, then blow it clean.
Top
Is too-frequent use of DRI WASH 'n GUARD® harmful to the
paint?
No. DRI WASH 'n GUARD® can be
applied daily without harming the painted surface. The
product works only as hard as necessary. On paint in
excellent condition, it cleans as gently as water. On
oxidized paint, DRI WASH 'n GUARD® cuts through layers of
oxidation each time it is used. The more DRI WASH 'n GUARD®
with exclusive formula PolyGuard-3® is used, the more
brilliant and smooth the surface becomes, and even more
resistant to the elements.
Top
What is "Cold Shock"?
The propellant in a typical
aerosol can will cause the can to become very cold after a
few minutes of continuous spraying. This cannot happen with
the AIRosol bottle because it is pressurized with ordinary
air.
Top
Can
DRI WASH 'n GUARD® be applied to vinyl tops?
Yes and no. DRI WASH 'n
GUARD® is not intended as a vinyl cleaner, but it will clean
vinyl without damage and will protect it. It is difficult,
however, to remove DRI WASH 'n GUARD® from the tiny grooves
in deeply grained vinyl. If it is used on vinyl, do not
allow it to dry to a haze before buffing of the vinyl
surface. Always test in inconspicuous area when using on
leather and vinyl surfaces.
Vinyl tops and leather upholstery will look like new again
with DRI WASH 'n GUARD® LEATHER & VINYL TREATMENT, which is
also available from any DWG International© independent
distributor.
Top
How about vinyl moldings, and leather or vinyl door trim
panels, padded instrument panel covers, tires, etc.?
See previous
question. It is almost impossible to polish a vehicle
without getting some of the DRI WASH 'n GUARD® on a vinyl
body molding, a rubber bumper fascia or bumper guard, or
flat-painted mirror, window molding or windshield wiper.
Just buff it off before it dries.
Top
I've noticed that some of the DRI WASH 'n GUARD® droplets
get past door, trunk and hood openings. Is it harmful to
leave them there?
No. Such over spray is
unavoidable. These droplets can be wiped off anytime, even
several months later.
Top
Is it really impossible to burn paint with a buffer when
using DRI WASH 'n GUARD®? What buffer speed is best?
Nothing is impossible,
but you'll have to try very hard. Under normal circumstances
it cannot happen. The surface simply becomes too slippery
and smooth to create the necessary friction (and heat) which
causes paint burn.
An orbital or a
variable-speed buffer at 1,500 RPM or less will do the job.
Do Not Buff With The Edge Of The Pad-use the entire pad
surface whenever possible. Operate the buffer using
unhurried, overlapping circular motions while maintaining
firm downward pressure.
Before attempting to use DRI WASH 'n GUARD® with a
high-speed buffer, you should be experienced in the usage of
a buffer and the differences in paint types with regards to
buffer use.
Top
What other
buffing tips do you suggest?
No one thing is recommended
for every situation. A buffer will do nothing for the paint
that polishing by hand can't do better or faster. Make sure
that the buffer is equipped with a foam bonnet.
Top
Can DRI WASH 'n GUARD® with exclusive formula PolyGuard-3®
remove swirls left in the paint by other products?
Yes. But you must buff in the
opposite direction of the swirl mark pattern, or in a
circular motion.
Top
How heavy should the
spray be?
More is not necessarily
better. Spray in long sweeping motions, holding the bottle
at least 12" from the surface.
Top
Can any other material be used as an applicator cloth when
applying DRI WASH 'n GUARD®?
The only recommended
substitute is a foam bonnet when using a buffer.
Top
Should DRI WASH 'n GUARD® be removed while still damp, or
let it dry completely?
Normally it makes no
difference, but in cases where the paint is in very poor
condition-dry, rough, oxidized-it is better to remove the
product immediately before moving to the next area.
Top
How many waterless wash/polish jobs can I expect from a
bottle of DRI WASH 'n GUARD®?
Using a new compact-size
vehicle as an illustration, the 8 oz. AIRosol applicator
should yield four polish jobs including glass. The 32-oz.
refill bottle should provide about 16 applications; the
64-oz. refill about 32.
Of course, the larger the vehicle,
or the worse the condition of the paint, the more DRI WASH
'n GUARD® you will use. But remember, a little goes a long
way!
Top
Beyond its durability, how often should DRI WASH 'n GUARD®
be reapplied to keep a vehicle looking really good?
To keep the incredible sense
of depth and brilliance in the paint, and to keep the
surface as smooth as porcelain, a monthly application is
recommended. Of course, that depends on the color and
condition of the paint and the weather conditions. Normally,
re-apply the product every 1-3
months.
Top
How economical
is DRI WASH 'n GUARD®?
If a 32 oz. bottle of DRI
WASH 'n GUARD® results in 16 cleaning/polishing jobs, you're
getting a bargain at a little over $2.00 each time. Compare
that with the $25-$50 cost of having your vehicle detailed.
Besides the money savings, a 32 oz. bottle will save more
than 2,000 gallons of water, an irreplaceable resource.
Top
Is DRI
WASH 'n GUARD® safe for clear coats?
Absolutely. DRI WASH 'n
GUARD® has been laboratory tested on every type of paint
used by the industry, from older acrylic lacquers to modern
high-gloss acrylic urethane and polyurethane paints.
Properly applied, DRI WASH 'n GUARD® with exclusive formula
PolyGuard-3® is safe for all hard non-porous surfaces. DRI
WASH 'n GUARD® should not be applied within 90 days of new
clear coat.
Top
How soon can DRI WASH 'n GUARD® be applied to a repainted
vehicle?
Both the paint industry and
the automobile industry generally endorse a 90-day waiting
period for newly painted vehicles, during which time
thinning solvents evaporate from the paint, allowing it to
cure. DWG
International endorses that industry standard.
Top
Are
there other uses for DRI WASH 'n GUARD®?
DRI WASH 'n GUARD® can be
effectively used on virtually any non-porous surface, from
automobile paint and chrome to household appliances to
jewelry. But you may want to try DRI WASH 'n GUARD® for the
Home, and DRI WASH 'n GUARD® Premium Metal Polish, too.
Top
Will DRI WASH 'n GUARD with exclusive formula PolyGuard-3®
work on boats and fiberglass?
Yes. With each application of
DRI WASH 'n GUARD®, the boat will be easier to maintain,
particularly against water spots.
Top
Will DRI WASH 'n GUARD® remove hard water spots?
It can, but only if the
finish is relatively new, has already been treated, or the
spotting hasn't set too deeply. DRI WASH 'n GUARD® is a
tremendous cleaner, but it is not an abrasive rubbing
compound, which often is necessary to remove severe hard
water spots.
Top
Does DRI WASH 'n GUARD® help to protect against ultraviolet
(UV) radiation?
Yes, thanks to two special
ingredients which help screen UV rays. But there is nothing
that can totally protect a surface from exposure to the sun.
Just as sunscreens cannot entirely protect the skin from
burning, UV- blockers cannot fully protect painted surfaces
from chemically decomposing over time.
Top
Can DRI
WASH 'n GUARD® remove scratches?
Yes, if they are minor, light
scratches. It will eliminate the tiny "feather" scratches
caused by many car wash brushes. The product does not
contain any ingredients which can fill deeper, more serious
scratches.
To remove light scratches, spray the scratched area with a
12" X 12" coat of DRI WASH 'n
GUARD®. Place a conventional high-speed buffer, with
a foam bonnet, directly against the scratched area. Turn the
buffer on while holding it in position, operate at 1,500 rpm
for 20 seconds without moving the buffer. Repeat once if
necessary.
Top
Can DRI WASH 'n GUARD® be
applied under direct sunlight or on a hot surface?
Yes, but
only if the product is buffed immediately.
If DRI WASH 'n GUARD® is allowed to "bake" into the
vehicle's finish, dark spots may appear beneath each
sprinkle. A garage is ideal, or a shaded area outside.
Top
